Analysis of the Biotribological Behavior for the Stainless Steel/Polyethylene Contact Using a Knee Prosthesis Simulator

摘要/Abstract

摘要：

In this work, a friction and wear simulator was used to reproduce the Anterior-Posterior (AP) sliding and the Flex-ion-Extension (FE) rotation generated in the knee joint during human gait cycle. We chose to simplify the contact geometry between the Total Knee Arthroplasty (TKA) femoral component and tibial insert. A 304L stainless steel cylinder which replaces the femoral component was loaded onto a flat High Density Polyethylene (HDPE) block which replaces the tibial insert. The tribological behavior of the considered contact was analyzed by tracking the number of cycles, the friction coefficient, the roughness of the wear track on HDPE, the HDPE weight loss and the damage mechanisms. The friction coefficient shows a gradual increase with the number of cycles for both AP and FE kinematics. The evolution of friction coefficient with the number of cycles is not affected by the value of the imposed normal load in the case of AP sliding. For the FE rotation, decreased friction coefficient is obtained when the imposed normal load increases. For both considered AP and FE kinematics, the roughness of the wear track on the HDPE is not affected by the imposed normal load. It shows a progressive decrease when the number of cycles increases. The wear of HDPE obeys the Archard law and the wear coefficient increases with the normal force. For a given value of normal load, the obtained wear coefficient for the AP sliding is larger than that obtained for FE rotation. A predominant adhesive wear mechanism was identified for both AP and FE kinematics. Under the same normal load, damage development in terms of plastic deformation, micro-cracking and debonding is more pronounced for the AP sliding if compared with the FE rotation. For a given kinematics, the damage severity increases with the normal load. This finding is in good agreement with the predicted values of the wear coefficient according to the Archard law.

关键词: knee, prosthesis, polyethylene, friction, wear, gait cycle

Abstract:

Key words: knee, prosthesis, polyethylene, friction, wear, gait cycle

M. Boujelbene, S. Dhouibi, M. Kharrat, M. Dammak. Analysis of the Biotribological Behavior for the Stainless Steel/Polyethylene Contact Using a Knee Prosthesis Simulator[J]. J4, 2012, 9(1): 59-65.

参考文献

[1] Freman M A R, Pinskerova V. The movement of the normal tibio-femoral joint. Journal of Biomechanics, 2005, 38, 197–208.

[2] Belvedere C, Leardini A, Giannini S, Ensini A, Bianchi L, Catani F. Does medio-lateral motion occur in the normal knee? An in-vitro study in passive motion. Journal of Biomechanics, 2011, 44, 877–884.

[3] Haider H, Walker P S. Measurements of constraint of total knee replacement. Journal of Biomechanics, 2005, 38, 341–348.

[4] Willing R, Kim I Y. Design optimization of a total knee replacement for improved constraint and flexion kinematics. Journal of Biomechanics, 2011, 44, 1014–1020.

[5] Des Jardins J D, Walker P S, Haider H, Perry J. The use of a force-controlled dynamic knee simulator to quantify the mechanical performance of total knee replacement designs during functional activity. Journal of Biomechanics, 2000, 33, 1231–1242.

[6] Chong D Y R, Hansen U N, Venne R, Verdonschot N, Amis A A. The influence of tibial component fixation techniques on resorption of supporting bone stock after total knee replacement. Journal of Biomechanics, 2011, 44, 948–954.

[7] Ketata H, Krichen A, Kharrat M, Dammak M. Mechanical response of polyethylene tibial component using compression loading contact test: Experimental and finite element analysis. Journal of Technology and Health Care, 2006, 14, 479–487.

[8] Xiong L, Xiong D S, Jin J B. Study on tribological properties of irradiated crosslinking UHMWPE nano-composite. Journal of Bionic Engineering, 2009, 6, 7–13.

[9] Cristofolini L, Affatato S, Erani P, Tigani D, Viceconti M. Implant fixation in knee replacement: Preliminary in vitro comparison of ceramic and metal cemented femoral components. Knee, 2009, 16, 101–108.

[10] Nikolov S, Han C S, Raabe D. On the origin of size effects in small-strain elasticity of solid polymers. International Journal of Solids and Structures, 2007, 44, 1582–1592.

[11] Saikko V, Ahlroos T, Calonius O. A three-axis knee wear simulator with ball-on-flat contact. Wear, 2001, 249, 310–315.

[12] Da Silva W M, Costa H L, De Mello J D B. Transitions in abrasive wear mechanisms: Effect of the superimposition of interactions. Wear, 2011, 271, 977–986.

[13] Dhouibi S, Boujelbene M, Kharrat M, Dammak M, Maalej A. Effects of sliding kinematics and normal load on the tribological behavior of metal/polymer contact. Materials Science and Engineering C, 2009, 29, 1521–1526.

[14] Massin P, Bonnin M, Paratte S, Vargas R, Piriou P, Deschamps G. Total knee replacement in post-traumatic arthritic knees with limitation of flexion. Orthopaedics & Traumatology: Surgery & Research, 2011, 97, 28–33.

[15] Jia B B, Li T S, Liu X J, Cong P H. Tribological behaviors of several polymer–polymer sliding combinations under dry friction and oil-lubricated conditions. Wear, 2007, 262, 1353–1359.

[16] Pal K, Pal S K, Das C K, Kim J K. Relationship between normal load and dynamic coefficient of friction on rock-rubber wear mechanism. Materials and Design, 2010, 31, 4792–4799.

[17] Li T Q, Zhang M Q, Song L, Zeng H M. Friction induced mechanochemical changes in high performance semicrystalline polymer. Polymer, 1999, 40, 4451–4458.

[18] Unal H, Sen U, Mimaroglu A. Dry sliding wear characteristics of some industrial polymers against steel counterface. Tribology International, 2004, 37, 727–732.

[19] Hutchings I M. Tribology Friction and Wear of Engineering Materials, CRC Press, Boca Raton, USA, 1992.