Technological Parameters and Design of Bionic Integrated Honeycomb Plates

doi:10.1016/S1672-6529(14)60028-7

J4 ›› 2014, Vol. 11 ›› Issue (1): 134-143.doi: 10.1016/S1672-6529(14)60028-7

收稿日期:2013-03-14 修回日期:2013-12-14 出版日期:2014-01-10 发布日期:2014-01-10

Technological Parameters and Design of Bionic Integrated Honeycomb Plates

Chenglong Gu, Jianxun Liu, Jinxiang Chen, Chenglin He, Yun Lu, Yong Zhao

1. School of Civil Engineering &|International Institute for Urban Systems Engineering,
Southeast University, Nanjing 210096, P. R. China
2. Department of Mechanical Engineering, Graduate School &|Faculty of Engineering,
Chiba University, Chiba 263-8522, Japan
3. System Consulting Dept. Aimnext Inc., Minato-Ku, Tokyo 105-0013, Japan

Received:2013-03-14 Revised:2013-12-14 Online:2014-01-10 Published:2014-01-10
Contact: Jinxiang Chen E-mail:chenjpaper@yahoo.co.jp
About author:Chenglong Gu, Jianxun Liu, Jinxiang Chen, Chenglin He, Yun Lu, Yong Zhao

摘要/Abstract

关键词: honeycomb, basalt fiber, bionic material, shear strength, compressive strength

Abstract:

We investigated an integrated manufacturing method to develop lightweight composite materials. To design the preparation process for the integrated honeycomb plates, the shear and compressive mechanical properties of the corresponding composite materials were also investigated. The results indicate that these composite materials, with two types of resins reinforced by short basalt fibers, exhibit obvious toughness, particularly in their compressive properties. The Epoxy Resin (ER) is denser and has better bonding at the fiber and matrix interface than the vinyl ester resin matrix. Therefore, the ER exhibits better shear and compressive strengths than the vinyl ester resin matrix, thereby providing a design technology of the preparation process of the integrated honeycomb plate. The matrix material of this plate is composed of an epoxy (E51), a curing agent (593), and a thinner (501) at a ratio of 10:3:1; short basalt fibers are added as a reinforcing material at a 30% volume fraction. By increasing the curing temperature and other experimental conditions, we obtained an expected integrated honeycomb plate. This integrated honeycomb plate possesses properties such as a high fiber content, good shear and compressive performance, and high proc-essing efficiency.

Key words: honeycomb, basalt fiber, bionic material, shear strength, compressive strength

Chenglong Gu, Jianxun Liu, Jinxiang Chen, Chenglin He, Yun Lu, Yong Zhao. [J]. J4, 2014, 11(1): 134-143.

Chenglong Gu, Jianxun Liu, Jinxiang Chen, Chenglin He, Yun Lu, Yong Zhao. Technological Parameters and Design of Bionic Integrated Honeycomb Plates[J]. J4, 2014, 11(1): 134-143.

参考文献

[1] Vincent J F V. Applications-some influences of engineering ideas on biology being the fifth in a series of essays on the materials of nature. Journal of Bionic Engineering, 2006, 3, 99–114.

[2] Dai Z, Yang Z. Macro-/micro-structures of elytra, me-chanical properties of the biomaterial and the coupling strength between elytra in beetles. Journal of Bionic Engi-neering, 2010, 7, 6–12.

[3] Thompson D W. On Growth and Form. Cambridge Uni-versity Press, New York, USA, 1961.

[4] Ma J F, Chen W Y, Zhao L, Zhao D H. Elastic buckling of bionic cylindrical shells based on bamboo. Journal of Bionic Engineering, 2008, 5, 231–238.

[5] Chen J, Iwamoto M, Ni Q Q, Kurashiki Q, Saito K. Cross sectional structure and its optimality of the forewing of beetles. Journal of the Society Material Science Japan, 2000, 49, 407–412. (in Japanese)

[6] Chen J, Ni Q, Xu Y, Iwamoto M. Lightweight composite structures in the forewings of beetles. Composite Structures, 2007, 79, 331–337.

[7] Chen J, Wu G. Beetle forewings: Epitome of the optimal design for lightweight composite materials. Carbohydrate Polymers, 2013, 91, 659–665.

[8] Hering G K. Method and device for joining sections of thermoplastic continuous web material. US Patent No. 7559351B2 (2009).

[9] Chen J, Gu C, Guo S, Wan C, Wang X, Xie J, Hu X. Inte-grated honeycomb technology motivated by the structure of beetle forewings. Materials Science and Engineering: C, 2012, 32, 1813–1817.

[10] Chen J, Xie J, Zhu H, Guan S, Wu G, Noori M, Guo S. Integrated hon-eycomb structure of a beetle forewing and its imitation. Materials Science and Engineering C, 2012, 32, 613–618.

[11] Czigány T. Special manufacturing and characteristics of basalt fiber reinforced hybrid polypropylene composites: Mechanical properties and acoustic emission study. Com-posites Science and Technology, 2006, 66, 3210–3220.

[12] Dalinkevich A A, Gumargalieva K Z, Marakhovsky S S, Soukhanov A V. Modern basalt fibrous materials and basalt fiber-based polymeric composites. Journal of Natural Fi-bers, 2009, 6, 248–271.

[13] Deák T, Czigány T. Chemical composition and mechanical properties of basalt and glass fibers: A comparison. Textile Research Journal, 2011, 79, 645-651.

[14] Sponton M, Mercado L A, Ronda J C, Galia M, Cadiz V. Preparation, thermal properties and ?ame retardancy of phosphorus- and silicon-containing epoxy resins. Polymer Degradation and Stability, 2008, 93, 2025–2031.

[15] Sun M L. The Application Principle and Technology of Epoxy Resin, Beijing Industry Press, Beijing, 2002. (in Chinese)

[16] Deak T, Czigany T, Marslkova M, Militky J. Manufacturing and testing of long basalt fiber reinforced thermoplastic matrix composites. Polymer Engineering & Science, 2010, 50, 2448–2456.

[17] Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures, American Concrete Institute, ACI440.3R-04.

[18] Fiber-Reinforced Plastics Composites–Determination of Compressive Properties, China National Bureau of Stan-dards, GB/T 1448-2005. (in Chinese)

[19] Li P M, Zhong C W, Qing M T, Pang X. Optimization of epoxy resin matrix composites for electronic packaging. Electronic Components and Materials, 2011, 30, 48–51. (in Chinese)

[20] Chen P, Wang D Z. Epoxy Resin and Its Application, Chemical Industry Press, Beijing, 2004. (in Chinese)

[21] Carmisciano S, De Rosa I M, Sarasini F, Tamburrano A, Valente M. Basalt woven fiber reinforced vinylester com-posites: Flexural and electrical properties. Materials & De-sign, 2011, 32, 337–342.

[22] Reifsnider K L, Mirzadeh F. Compressive strength and mode of failure of 8H celion 3000/PMR15 women compos-ite material. Journal of Composites Technology & Research, 1988, 10, 156–164.

[23] Liu Q, Shaw M T, Parnas R S. Investigation of basalt fiber composite mechanical properties for applications in trans-portation. Polymer Composites, 2006, 27, 41–48.

[24] Mahesh S. Deformation banding and shear banding in single crystals. Acta Materialia, 2006, 54, 4565–4574.

[25] Cheng J H, Ghosh S. Computational modeling of plastic deformation and shear banding in bulk metallic glasses. Computational Materials Science, 2013, 69, 494–504.

[26] Vas L M, Czigany T. Strength modeling of two-component hybrid fiber composite sincase of simultaneous fiber failures. Journal of Composite Materials, 2006, 40, 1735–1762.

[27] Aay T C, Poloskei K, Karger-Kocsis J. Fracture and failure behavior of basalt fiber mat-reinforced vinylester epoxy hybrid resins as a function of resin composition and fiber surface treatment. Journal of Materials Science, 2005, 40, 5609–5618.

[28] Anderson B J. Thermal stability of high temperature epoxy adhesives by thermo-gravimetric and adhesive strength measurements. Polymer Degradation and Stability, 2011, 96, 1874–1881.

[29] Wang Z M. Mechanics and Structure Mechanics of Com-posite Materials, China Machine Press, Beijing, 1991. (in Chinese).

Technological Parameters and Design of Bionic Integrated Honeycomb Plates

PDF (PC)

赞

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 2

Metrics

本文评价

推荐阅读 10

[1]	Nor Azlina Ramlee, Mohammad Jawaid, Edi Syams Zainudin, Shaikh Abdul Karim Yamani. Modification of Oil Palm Empty Fruit Bunch and Sugarcane Bagasse Biomass as Potential Reinforcement for Composites Panel and Thermal #br# Insulation Materials[J]. Journal of Bionic Engineering, 2019, 16(1): 175-188.
[2]	Dan Zhou, Yan Gao, Ming Lai, Hao Li, Bin Yuan, Min Zhu. Fabrication of NiTi Shape Memory Alloys with Graded Porosity to Imitate Human Long-bone Structure[J]. J4, 2015, 12(4): 575-582.