The Effect of Non-Contact Conditions in a Splinted Fixed Partial Denture on the Load Sharing Mechanism: A Finite Element Study

doi:10.1016/S1672-6529(11)60122-4

摘要/Abstract

摘要：

A computer-aided design model for a fixed partial denture was constructed and used in a finite element analysis to study the overall load sharing mechanism between the fixed partial denture and oral structures while the denture base rested on the alveolar ridge. To investigate the consequences of non-contact conditions, three additional models were generated incorporating a uniform clearance of 0.125 mm, 0.25 mm, and 0.5 mm, respectively. A 100 N static load located at the free end of the pros-thesis was applied while the distal portion of the jaw was set fixed. The results show that whilst releasing the ridge almost entirely, the presence of the clearance drastically increased the load on the splinting teeth. A pull-out force on the canine tooth of about 44 N was computed, accompanied by a mesio-distal moment of about 500 N?cm. The combination of which was similar to the tooth extraction maneuver performed by the dentist. In contrast, the second premolar was found to bear a push-in force of almost 115 N. The first molar, though barely solicited in the contact condition, became substantially loaded in non-contact conditions, which validates the choice of sacrificing three teeth to support the denture.

关键词: finite element analysis, splinted fixed partial denture, hygienic space, load transfer mechanism, contact problem

Abstract:

Key words: finite element analysis, splinted fixed partial denture, hygienic space, load transfer mechanism, contact problem

M. Z. Bendjaballah. The Effect of Non-Contact Conditions in a Splinted Fixed Partial Denture on the Load Sharing Mechanism: A Finite Element Study[J]. J4, 2012, 9(3): 336-342.

参考文献

[1] Wostmann B, Budtz-Jorgensen E, Jepson N, Mushimoto E, Palmquist S, Sofou A, Owall B. Indications for removable partial dentures: A literature review. International Journal of Prosthodontics, 2005, 18, 139−145.

[2] McGivney G P, Castleberry D. McCracken’s Removable Partial Prosthodontics, 9th ed, The CV Mosby Company, St Louis, USA, 1995.

[3] Mijiritsky E, Karas S. Removable partial denture design involving teeth and implants as an alternative to unsuccessful fixed implant therapy: A case report. Implant Dentistry, 2004, 13, 218−222.

[4] Block M S, Kent J N. Prospective review of integral implants. Dental Clinics of North America, 1992, 36, 27−37.

[5] El-Wakad M T, Bendjaballah M Z. Finite element study of Load transfer in a splinted fixed partial denture. Egyptian Dental Journal, 2010, 56, 375−381.

[6] Lin C L, Wang J C, Chang W J. Biomechanical interactions in tooth-implant-supported fixed partial dentures with variations in the number of splinted teeth and connector type: A finite element analysis. Clinical Oral Implants Research, 2008, 19, 107−117.

[7] El-Wakad M T. Effect of splinting in a fixed partial denture on bone response: FEM study. Egyptian Dental Journal, 2009, 55, 1999−2005.

[8] El Charkawi H G, El-Wakad M T. Effect of splinting on load distribution of extracoronal attachment with distal extension prosthesis in vitro. Journal of Prosthetic Dentistry, 1996, 63, 315−320.

[9] Menicucci G, Ceruti P, Barabino E, Screti A, Bignardi C, Preti G. A preliminary in vivo trial of load transfer in mandibular implant-retained overdentures anchored in two different ways, allowing and counteracting free rotation. International Journal of Prosthodontics, 2006, 19, 574−576.

[10] Sadowsky S J, Caputo A A. Effect of anchorage systems and extension base contact on load transfer with mandibular implant-retained overdentures. Journal of Prosthetic Dentistry, 2000, 84, 327−334.

[11] Sadowsky S J, Caputo A A. Stress transfer of four mandibular implant overdenture cantilever designs. Journal of Prosthetic Dentistry, 2004, 92, 328−336.

[12] Jacobson T E, Krol A J. A contemporary review of the factors involved in complete dentures. Part III: Support. Journal of Prosthetic Dentistry, 1983, 49, 306−313.

[13] Pietrabissa R, Contro R, Quaglini V, Soncini M, Gionso L, Simion M. Experimental and computational approach for the evaluation of the biomechanical effects of dental bridge misfit. Journal of Biomechanics, 2000, 33, 1489−1495.

[14] Yamashita J, Wang Q, Dechow P C. Biomechanical effects of fixed partial denture therapy on strain patterns of the mandible. The Journal of Prosthetic Dentistry, 2006, 95, 55−62.

[15] Field C, Li Q, Li W, Swain M V. Biomechanical response in mandibular bone due to mastication loading on 3-unit fixed partial dentures. Journal of Dental Biomechanics, 2010, 2010, 902537.

[16] Li Q, Li W, Thompson M, Swain M V. Prediction of mandibular bone remodeling induced by fixed partial dentures. Journal of Biomechanics, 2010, 43, 1771−1779.

[17] Grant A A, Heath J R, McCord J F. Complete Prosthodontics, Problems, Diagnosis, and Management, Mosby-Wolfe, London, UK, 1995.

[18] Liedberg N B, Owall B, Stultze K. Masticatory and nutritional aspects on fixed and removable partial dentures. Clinical Oral Investigation, 2004, 8, 11−17.

[19] Eraslan O, Sevimay M, Usumez A, Eskitasciioglu G. Effects of cantilever design and material on stress distribution in fixed partial dentures: A finite element analysis. Journal of Oral Rehabilitation, 2005, 32, 273−278.

[20] Lyons K M, Beumer J. Abutment load transfer by removable partial denture obturator framework in different acquired maxillary defects. Journal of Prosthetic Dentistry, 2005, 94, 281−288.

[21] Yang H S, Lang L A, Felton D A. Finite element analysis on the effect of splinting in fixed partial dentures. Journal of Prosthetic Dentistry, 1999, 81, 721−728.

[22] Huang H L, Huang J S, Ko C C, Hsu J T, Chang C H, Chen M Y. Effects of splinted prosthesis supported a wide implant or two implants: A three dimensional finite element analysis. Clinical Oral Implants Research, 2005, 16, 466−472.

[23] Holmes D C, Loftus J T. Influence of bone quality on stress distribution for endosseous implants. Journal of Oral Implantology, 1997, 23, 104−111.

[24] Bendjaballah M Z, El-Wakad M T. Prediction of the optimum number of teeth supporting a long fixed partial denture: A finite element model study. The 12th International Conference of Machine Design and Production, Kusadasi, Turkey, 2006, 5−8.

[25] Chun H J, Cheong S Y, Han J H, Heo H J, Chung J P, Rhyu I C, Choi Y C, Baik H K, Ku Y, Kim M H. Evaluation of design parameters of osseointegrated dental implants using finite element analysis. Journal of Oral Rehabilitation, 2002, 29, 565−574.

[26] Holmgren E P, Seckinger R J, Kilgren L M, Mante F. Evaluating parameters of osseointegrated dental implants using finite element analysis: A two dimensional comparative study examining the effects of implant diameter, implant shape, and load direction. Journal of Oral Implantology, 1998, 24, 80−88.

[27] Biamonte T, Abbate M F, Pizzarello F, Lozada J, James R. The experimental verification of the efficacy of the finite element modeling to dental implant systems. Journal of Oral Implantology, 1996, 22, 104−110.

[28] Stegaroiu R, Sato T, Kusakari H, Miyakawa O. Influence of restoration type on stress distribution in bone around implants: A three-dimensional finite element analysis. International Journal of Oral Maxillofacial Implants, 1998, 13, 82−90.